Products

Introduction to products

Date:2011/1/19 22:09:28  0

PRODUCT NAME SLJ40 Chlorinated Rubber antifouling paint

BRIEF Made from chlorinated rubber, plasticizer, functional materials, pigments, additives, etc

FEATURES  
-Good adhesion and anti-fouling ability, Long-term prevention of marine fouling organisms to the hull adhesion
-Keep the bottom clean, save fuel and prolong the maintenance intervals of time
-Construction is convenient, quick drying, construction of basic is not restricted
by seasonal temperatures

RESISTANCE GUIDE
 HEAT RESISTANCE Up to 65℃ dry heat
 WEATHERABILITY Good
 SOLVENTS Resists splash and spillage of most aliphatic solvents and mineral oil.
 ACIDS Suitable for splash and spillage exposure to most inorganic acids.
 ALKALIS Suitable for splash and spillage of most alkalis
 SALTS Suitable for splash and spillage of most alkali salts
 WATER Excellent resistance to splash and spillage of fresh and salt water
 ABRASION Good
RESISTANCE GUIDE
HEAT RESISTANCE   Up to 65℃ dry heat
WEATHERABILITY   Dulling and crack with long-term exterior exposure
SOLVENTS               Resists splash and spillage of most aliphatic solvents and most alcohols solvents
ACIDS                       Suitable for splash and spillage exposure to most solutions of  weak acids.
ALKALIS                   Suitable for splash and spillage of most alkalis
SALTS                       Suitable for splash and spillage of most alkali salts
WATER                     Soak in the water

USES:  Widely used in hull bottom, offshore facility, oil platform, drogue, wharf, in case of sea creatures adhesion and growth, and on the surface of the concrete corrosion.

TYPICAL PROPERTIES AND APPLICATION DATA
COLOR                         Red Brown
DENSITY                       1.9g/cm3
SOLIDS BY VOLUME              48%
SOLIDS BY WEIGHT               80%
SPREADING RATE                4.2 m2/kg      (60um DFT)
DRYING TIME(23℃)              Touch  4 Hr    Handle  24 Hr   
OVERCOAT INTERVAL(23℃)        Min 4 Hr   Max 24 Hr
Drying time before launching(23℃)    24 Hr
STORAGE                                at least 12 months (dry, cool and under cover )
PACKAGING                            25kg

DIRECTIONS Before using stir or using dynamic mixer mixing two components completely. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity after stir. Overmuch thinner will lead sag and slow cure rate, thin film, thinner should beadded after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.
24 hours later must be in the water after finally coated..

APPLICATION  

STEEL: The surfaces coated by primer or intermediate paint must dry, remove oil, grease
and other pollutants When overcoat on a two-component primer, wharf's pavementquality for old film or high-pressure water injection processing should be taken if more than the longest accordance with time.
Don’t apply at temperatures below -10℃ or above 40℃. Don’t apply at relative humidity above 85% or when the surface is less than 3℃ above the dew point. In construction of lower than 0 ℃, the coated surface shall be free of ice, snow, etc.
Don’t apply if there is fog, rain, snow or strong wind.
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with X-3 Thinner X-3. Additional coats may be required to attain specified thickness.
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Chlorinated Rubber Thinner X-3 can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Chlorinated Rubber Thinner X-3 can be added. Pump ratio is 23:1 or 32:1 and fluid tip is 0.33-0.38 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
Previous coat: Epoxy Coatings, Chlorinated Rubber Coatings
CLEAN UP: with Chlorinated Rubber Thinner X-3



SAFETY:Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.

 

Copyright © 2003-2014 www.sfcoat.com, All Rights Reserved  备案号:鲁ICP备17000082号-1
Address:Dongying City, Shandong Province, Hong Xia Road 7 underground Tel:0546-8747889
Fax:0546-8642167 www.546dns.cn