Products

Introduction to products

Date:2015/11/12 11:31:08  0

PRODUCT NAME Chlorinated Rubber Coat SLBT04

BRIEF  One Pack anti-rust oil made from variety of resins, special preservatives, pigment, etc

FEATURES
-Excellent anti-aging and resistance to corrosion medium
-Excellent resistance to hot and humid, salt fog resistance
-Excellent resistance to pulverization and crack
-High gloss, quick drying
-Excellent camouflage and optical performance

RESISTANCE GUIDE

Excenllent anticorrosion performance for all kinds of metals and their
products.
Excenllent anticorrosion for large quantities of metal products in open
air under special circumstances, such as tubing, rail, steel pipe, etc

USES:Widely used on steel surface of tubing, rail, steel tube, machine tools, etc

 TYPICAL PROPERTIES AND APPLICATION DATA
COLOR                         Colors
OSITY (TU - 4 CUPS)                 10~30s
ADHESIVE                      ≤2  class
MALLEABILITY                      ≤2mm
SOLIDS BY WEIGHT               40%
SALT FROG                      ≥72 Hr
DRYING TIME(23℃)              Touch  30min    Handle  24 Hr 
 
 DIRECTIONS   Primer(glue), Intermediate(glue), Topcoat(glue) is a two pack, before using stir or using dynamic mixer mixing two components completely, then add part B to part A, and fully stir, life for 4 hours. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity afterstir. Overmuch thinner will lead sag and slow cure rate, thin film, thinner should be added after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.
 
 APPLICATION   

STEEL: Remove the surface of oil, grease and other pollutants.
Don’t apply at temperatures below 5℃ or above 40℃. Don’t apply at relative humidity above 85% or when the surface is less than 3℃ above the dew point. In construction of lower than 0℃, the coated surface shall be free of ice, snow, etc.
Don’t apply if there is fog, rain, snow or strong wind.
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with Special Thinner X-13 Additional coats may be required to attain specified thickness.
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Special Thinner X-13 can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Special Thinner X-13 can be added.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
CLEAN UP: with Special Thinner X-13

SAFETY:  Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.


Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.

 

Copyright © 2003-2014 www.sfcoat.com, All Rights Reserved  备案号:鲁ICP备17000082号-1
Address:Dongying City, Shandong Province, Hong Xia Road 7 underground Tel:0546-8747889
Fax:0546-8642167 www.546dns.cn