Products

Introduction to products

Date:2011/1/19 21:56:36  0

PRODUCT NAME SLH53 Epoxy-MIO Anti-rust Coatings

BRIEF Two Pack Epoxy Micaceous Iron Oxide Sealer/middle paint-MIO Coating

FEATURES  
-Used as primer, sealer or intercoat
-Excellent adhesion and sealing power on prepared substrate, good adhesion to next coat
-Good resistance to abrasion and impact
-Can be exposed to atmosphere and immersed in water

RESISTANCE GUIDE
HEAT RESISTANCE   Up to 140℃ dry heat.
WEATHERABILITY      Some chalking will occur with exterior exposure.
SOLVENTS                  Resists immersion of most petroleum solvents,  gasoline,
diesel oil and lubricating oil.
ACIDS               Suitable for splash and spillage to mild acids.
ALKALIS           Exellent for splash and spillage to most alkalis.
SALTS               Resists immersion of neutral and alkali salts.
WATER             Excellent resistance to immersion in fresh and salt water.
ABRASION      Good when fully cured.
        
USES:Widely used in Ship, oil platform, bridge, marine facilities, pipeline, etc.

TYPICAL PROPERTIES AND APPLICATION DATA 
 COLOUR                        Brown Red, Grey
 DENSITY                        1.4Kg/cm3
 SOLIDS BY VOLUME             58%
 SOLIDS BY WEIGHT              76%
 SPREADING RATE               4.1 m2/kg (100um DFT)
 DRYING TIME(23℃)            Touch  3 Hr    Handle  24 Hr    Full cure 7Days
 OVERCOAT INTERVAL(23℃)      Min 8 Hr   Max 7 Days 
 STORAGE (dry, cool )          At least 12 months
 PACKAGING                          Part A: 21kg   Part B: 3kg 
 MIXING RATIO (m/m)           Part A : Part B=7:1
 CURE TIME(23℃)               10min 
 POT LIFE(23℃)                   4Hr

DIRECTIONS  Before using stir or using dynamic mixer mixing two components completely,Just mix a good raw material and mixing of raw materials before can not be together. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity after stir.
Overmuch thinner will lead sag and slow cure rate, thin film, thinner should be added after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.

APPLICATION  

STEEL:Steel surface must be prepared by abrasive blast cleaning to ISO Standard Class Sa2.5 or power tool cleaning Class St3. Surface should be dry, clean and no dirt, take the second descaling where film damaged or corrosion, and achieve Sa2.5 level or St3 level.
Don’t apply at temperatures below 5℃ or above 40℃. Don’t apply at relative humidity above 85% or when the surface is less than 3℃ above the dew point.
Don’t apply if there is fog, rain, snow or strong wind.
BRUSH/ROLLER:Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with Epoxy Thinner X-2. Additional coats may be required to attain specified thickness. 
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Epoxy Thinner X-2 can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-15% of Epoxy Thinner X-2 can be added. Pump ratio is 23:1 or 32:1 and fluid tip is 0.38-0.43 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
Previous coat: Zinc Rich Epoxy Primer, Anti-rust Epoxy Primer.
CLEAN UP:
with Epoxy Thinner X-2.


SAFETY: Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

 

Copyright © 2003-2014 www.sfcoat.com, All Rights Reserved  备案号:鲁ICP备17000082号-1
Address:Dongying City, Shandong Province, Hong Xia Road 7 underground Tel:0546-8747889
Fax:0546-8642167 www.546dns.cn