PRODUCT NAME SLH52 Epoxy Coal Tar Pitch Anti-rust Paint

BRIEF  One Pack fast-drying paint made from Epoxy ester resin, additives, zinc
chromate antirust paint, etc

FEATURES 
-Excellent adhesion on steel
-Excellent anti-rust ability
-As a general primer chlorinated rubber or acrylic paint
-Not suitable for strong alkaline environment

RESISTANCE GUIDE
HEAT RESISTANCE     Up to 80℃ dry heat
WEATHERABILITY        Fine
SOLVENTS          Resists to alcohol, mineral turpentine oil and other solvents.
ACIDS                   Don't recommend contact the overflow of acid fog, acid and spatter.
ALKALIS               Unfavorable contact alkali fog, lye overflows and spatter.
SALTS                  Not resistant to most of the salt solution.
WATER                Excellent resistance to rain and moisture, do not use under the condition of damp and soak for a long time.
ABRASION          Good when fully cured.


USES:  Suitable for surface of the steel the in mildly to moderately corrosive atmospheric environment .

TYPICAL PROPERTIES AND APPLICATION DATA
COLOR                        Brown Red etc
DENSITY                       1.34g/cm3
SOLIDS BY VOLUME              55%
SOLIDS BY WEUGHT             72%
SPREADING RATE                8.21m2/kg   (40um DFT)
DRYING TIME(23℃)              Touch  4 Hr    Handle  24 Hr
OVERCOAT INTERVAL(23℃)        Min 24 Hr  
STORAGE                           at least 12 months (dry, cool and under cover )
FLASH POINT                    28℃
PACKAGING                       20kg/ bucket

DIRECTIONS  Before using stir or using dynamic mixer mixing two components completely,Just mix a good raw material and mixing of raw materials before can not be together. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity after stir.
Overmuch thinner will lead sag and slow cure rate, thin film, thinner should be added after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.

APPLICATION  

STEEL: Steel surface must be prepared by abrasive blast cleaning to ISO Standard Class Sa2.5 or power tool cleaning Class St3. Primer surface must keep dry and clean. The primer surface of damage, wedding and rusting must be prepared to Sa2.5 or St3. Zinc salt on the primer must be removed by abrasive or fresh water blasting.
Don’t apply at air temperature below 5℃ or above 40℃. Don’t apply at relative humidity above 85% or when air temperature is less than 3℃ above the dew point.
Don’t apply if there is fog, rain, snow or strong wind. 
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with Epoxy Thinner X-2. Additional coats may be required to attain specified thickness. 
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Epoxy Thinner X-2 can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Epoxy Thinner X-2 can be added. Pump ratio is 45:1 and fluid tip is 0.48-0.64 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants. Also can be applied in sequence of coat, glass cloth, coat.  
Recommended previous coat: Zinc Rich Epoxy Primer, Epoxy Anti-rust Primer, Epoxy MIO Intercoating.
Previous coat:  Zinc Silicate Primers, Epoxy Antirust Primer
CLEAN UP: with Epoxy Thinner X-6.

SAFETY:Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.